Square-stern Canoe With 2.5 Mercury outboard Part 1 – YouTube
Dave's square stern canoe with 2.5 Mercury outboard. Its a great motor , I needed to put an anti-cavitation plate on, to reduce spray into the canoe as I have a side mount, I use outriggers to balance the motor when its up. love the electronic ignition … View Video
Lil' Fella Instructions
#462 Little Brother to the HAPPY TROLLER ® For Outboard Motors Up To and Including 25 Horsepower INSTALLATION INSTRUCTIONS Step 1: Remove the Step 3: Locate the anti-cavitation plate on your motor or outdrive. It's the wide horizontal plate which extends just above the propeller. … Retrieve Full Source
Propeller (marine) – Wikipedia, The Free Encyclopedia
A failed rubber bushing in an outboard's propeller. For smaller engines, such as outboards, where the propeller is exposed to the risk of collision with heavy objects, the propeller often includes a … Read Article
SUZHOU P OUTBOARD MOT ARSUN POWER MACHINE CO., L
Install the outboard motor on the test tank. 1. Lowest water level 2. Water surface. 1 2 5. Fill the tank with fresh water to above the level of the anti-cavitation plate. … Fetch Here
Copyright © 2007 Tohatsu Corporation
This will cause poor starting, reduced power and may damage your motor. Use good quality fuel and lubricants at all times. (2) Mounting the outboard motor 11 Position: The center of the stern (Fig. 21 2) Height: Fit the outboard so that the anti-cavitation 'plate is lower than the bottom of the boat by 3 … Fetch Full Source
Cavitation – Wikipedia, The Free Encyclopedia
Cavitation damage on a valve plate for an axial piston hydraulic pump. Cavitation is the formation and then immediate implosion of cavities in a liquid – i.e. small liquid-free zones ("bubbles") – that are the … Read Article
OUTBOARD MOTORS
If outboard motor mounts are not checked regularly, the engine can shake loose and fresh water (water level above the anti-cavitation plate). Put the motor into neutral, … Get Doc
Happy Troller Instructions
Large size fits inboard/outboard and outboard motors 50 hp and larger. Small size is for 20-50 hp. Step 3: Locate the anti-cavitation plate on your motor or outdrive. It's the wide flange directly above the propeller. … Access Content
OPERATOR’S MANUAL Model Numbers F4ETS, F4ETL, F4ERS, F4ERL
outboard motor so that the anti-cavitation plate is between the bottom of the boat and a level 25mm below it. NOTE: The optimum mounting height of the outboard motor is affected by the boat and motor … Content Retrieval
Through-the-prop Exhaust Is Used To Achieve Nice, Quiet …
The outboard can be turned to any direction, up to 360 degrees, for simple steering that is needed for of the motor for easier operation. Wide anti-cavitation plate with trim tab … Access Doc
Copyright © 2007 Nissan Marine Co. Ltd.
(4) Trim angle The outboard motor is adjustable its trim angle depending on stern angle of a boat and loading condition. Choose appropriate trim angle of the motor that the anti-cavitation plate is parallel to water face while running *Proper trim angle When the boat is holi-zontal while running, a … Fetch Document
Thank You For Purchasing A Honda Outboard Motor.
The motor should be installed so that the anti-cavitation plate is 2-5 cm (0.8-2.0 in) below the bottom of the boat. 2 hour or longer (be sure the water level is at least 4 inches above the cavitation plate). 7. As soon as possible, take the motor to a Honda outboard … Fetch This Document
Thank You For Purchasing A Honda Outboard Motor.
Loading too much or too far rearward will push the motor deeper, reducing performance. CAUTION: Insufficient water supply (anti-cavitation plate out of the water) may cause overheating that will damage the outboard motor. 8 … Get Content Here
Through-the-prop Exhaust Is Used To Achieve Nice, Quiet …
Of the motor for easier operation. Wide anti-cavitation plate with trim tab Nissan Marine's uniquely designed 6 hp, 4-stroke motor is ideal for sailboats or any marine vessel requiring a 25" shaft outboard motor. … Fetch Doc
Mercury KG-7Q Super 10 Hurricane – Wikipedia, The Free …
Mercury KG-7Q Super 10 Hurricane is an outboard motor built by Kiekhaefer Mercury during the years of 1950 through 1952. In addition the motor had a sort-of cut down lower anti-cavitation plate, protruding forward upper anti-cavitation plate (spray plate), a stronger rear-mounted steering … Read Article
Copyright © 2007 Tohatsu Corporation
(4) Tilt angle The outboard motor is adjustable its tilt angle depending on stern angle of a boat and loading condition. Choose appropriate tilt angle of the motor that the anti-cavitation plate is paralel to water face while running. aProper tilt angle When the boat is holi-zontal while running, a … Fetch Content
OPERATOR’S MANUAL Model Numbers F4ETS, F4ETL, F4ERS, F4ERL …
outboard motor so that the anti-cavitation plate is between the bottom of the boat and a level 25mm below it. 0～25mm (0-1in) NOTE: The optimum mounting height of the outboard motor is affected by the boat and motor … Fetch Content
Copyright © 2007 Nissan Marine Co. Ltd.
STOPPING THE ENGINE F We @ Push the stop switch and release it after the engine has stopped, or remove the safety switch lock. and raise up the outboard motor l Do not expose the anti-cavitation slightly. It can then be returned to plate to air. the normal cruising position. 37 … Retrieve Document
The outboard Can Be Turned To Any Direction, Up To 360 …
The outboard can be turned to any direction, up to 360 degrees, for front of the motor, allows the steering friction to be adjusted for both steady running at high speed and easier maneuvering while trolling. <20/15> Wide anti-cavitation plate … Fetch Document